Bulldog Brewer to be delivered on Tuesday!

The Homebrew Forum

Help Support The Homebrew Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

MoBlo

#DutchCourage
Joined
Jan 10, 2016
Messages
16
Reaction score
4
Location
West Yorkshire
Hi all!

Joined about a year and a half ago, when we did our first small brew kit, but I have since been both busy with finishing a PhD and longing for a set-up that would not involve loads of pans, sieves and stress to get everything working properly, and also would allow us to brew slightly larger quantities more easily.

So, after some dreaming and thinking, soul searching and internet searching, we've decided to go with a Bulldog Brewer 30L (25L capacity)! It's not a Braumeister or a Grainfather, but we don't want to spend that amount of money just yet. We've seen some good reviews on Youtube and felt it was going to be good value for money.

Very excited to get started, but would love to hear some DO's and DON'Ts from other Bulldog Brewer owners. Some must haves to order as well to complement the set up, for example, or some minor tweaks that will make life easier?
 
I have heard no complaints from owners, although there aren't very many of them. I think the external pump and silicon pipework makes them look less pretty than the ACE, so that wins some buyers over. But it won't make it brew beer any worse.
For the money the Bulldog is a very good choice, especially with the stainless steel chiller.
 
I have heard no complaints from owners, although there aren't very many of them. I think the external pump and silicon pipework makes them look less pretty than the ACE, so that wins some buyers over. But it won't make it brew beer any worse.
For the money the Bulldog is a very good choice, especially with the stainless steel chiller.

Yes, we had a look at the ACE as well, but the Bulldog seemed a bit more user-friendly. And as you said, it's about the brew, not about aesthetics, at this point. That'll come into play when I've reached my goal of opening up a brew pub and want some lovely looking set-up ;)
 
Hey Mo,
I've got a Bulldog Brewer and I'm very happy with it. It certainly makes it quicker, easier and less messy than when I do BIAB. If you are ordering now you will get one of the more recent ones and they've worked through the teething problems. A few tips:

Crush: If you crush your own grain then 1.0-1.2mm mill gap size works perfectly for me. Pre-crushed grain varies in how finely it is milled, but should mostly be fine, but I would get in some rice or oak husks so you can chuck 100g or so in the grist just in case it is too finely milled. Definitely use husks if you have a sizeable amount of wheat or rye in the grist.

Strike water: Heat up the strike water on full power to get to your desired strike water temperature, then turn the power down to 700W and the temp to mash temp, then dough in. Strike water volume should be about 3.0 L/kg, though I've had success with lower; for large grain bills 3.0L/kg might leave the water line above the overflow pipe so instead of recirculating through the grain it just recirculated through the pipe. It is best to check with the “can I mash it” tool for big beers. Its probably a good idea to check the strike and mash temperature with a seperate thermometer to make sure your unit is well calibrated, and make adjustments accordingly if needs be.

Mash: Start the recirculation slowly by partly closing the ball valve to avoid drawing in the grain bed. You can always put on the sparge plate to dispurse the wort and avoid creating channels in the mash. I do stir half way just to loosen the mash. This isn't a problem because it only takes a few minutes to settle the grain bed and get clear wort running through again. Always do a mash out, because you can. If you aren't using the pump for the sparge then I recommend rinsing it through immediately after the mash to prevent sticky wort from drying in there and potentially gumming it up.

Sparge: Be careful lifting up the malt pipe. I always push out sideways on the handle when lifiting because otherwise the handle can slip. Apparently they had solved this problem when I bought mine but it still a bit dodgy. For volumes, dead space and trub loss is about 2.5L. Also, as you are doing a mash out then the sparge water doesn't need to be as hot because you don't have to raise the temperature of the grain. I mash out and sparge at 76C to good effect.

Boil: Even though Bulldog have said you can use the malt pipe as a hop spider, don't do it. It screws up the boil and shoots out the overflow pipe. I use 5 gallon nylon bags to keep the hops in. These ones fit well, don't reach to the bottom, but still are big enough for the hops to move about freely to give you decent utilisation. Leaf hops might be ok, but I find that that with pellets then the bazooka filter clogs without a spider/bag. I always squeeze the hop bag after the boil, especially if I'm using expensive aroma/flavour hops. Many people bring to the boil at 2500W then reduce it to 1800W for a decent rolling boil with about 4L/hour boil off, though I prefer overshooting with the sparge to get better efficieny then just boiling down at 2500W. If you do this then having a spray bottle handy to prevent boil over.

Cooling: Once it gets down to 80C or so I turn on the recirculation pump. Not only does this help agitate the wort and speed up chilling, but you also end up with crystal clear wort in the fv.

Hope this helps and happy brewing!
 
Last edited by a moderator:

Latest posts

Back
Top