Your First Grainfather Brew - A Walkthrough

The Homebrew Forum

Help Support The Homebrew Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Thanks for this Steve, I did my first brew on my new GF yesterday and this was a massive help...

Only a couple of self inflicted minor hiccups.

1. I managed to undo the check valve taking the sparge arm off in the middle of the mash, the close up picture of this saved me a lot of messing about.
2. I also managed to pull the telescopic pipe up too far and got unfiltered wort in the kettle so I ended up with cloudy wort but that will clear up.
3. The sparge was a bit slow and I had to poke it around a bit, so I'll get some rice hulls next time I put an order in.

Thanks again for the great guide!
 
Thanks for this Steve, I did my first brew on my new GF yesterday and this was a massive help...

Only a couple of self inflicted minor hiccups.

1. I managed to undo the check valve taking the sparge arm off in the middle of the mash, the close up picture of this saved me a lot of messing about.
2. I also managed to pull the telescopic pipe up too far and got unfiltered wort in the kettle so I ended up with cloudy wort but that will clear up.
3. The sparge was a bit slow and I had to poke it around a bit, so I'll get some rice hulls next time I put an order in.

Thanks again for the great guide!

Just a hint, but when i lift the grain basket for sparging, i tend to give the grain bed a paddlin' just to filter around what has generally got stuck through all holes in the bottom mash plate and since doing that, I have no stuck sparge issues and no issue hitting my efficiency targets.

Be careful when running the paddle around to make sure you don't provide too much down-pressure as sometimes the bracket thingy the grain basket sits on can fall out, then it becomes a massive pain to rectify (two man job, someone to replace the grain basket bracket whilst someone else holds up several kilos of hot, wet grain) but that has only happened to me once.
 
Leave the basket sitting in place to drain until the wort gets up near boiling point, but be sure to remove it before it actually starts boiling. This is a surefire way of having a boil over. By the time the wort gets to mid 90s the basket should be well drained, so set it aside for now and turn your attention back to the GF.

Be sure to keep the lid off from now until the end of the boil. As the wort comes to the boil it'll begin to foam up. Stir this back in to prevent boil overs, it'll settle down after a few minutes.

GnnHMap.jpg


As soon as you have a nice rolling boil, start a timer with your boil time and add the hops as per your recipe.

Every 15 mins or so during the boil, take your paddle and gently scrape the bottom of the boiler to prevent proteins scorching on the bottom.

Now is a good time to dispose of the used grain and clean the grain basket, plates, pipe work and overflow inlet. I do this outside because it can be a bit messy. Dismantle all the various parts and rinse under a tap. Use a non-scratch scouring sponge to remove any stubborn residue.

Once these bits are clean and dry, they can be put aside for storage, you're done with them for today.

Towards the end of the boil you want to start thinking about sanitising the FV. I do this by giving it a rinse out with boiling water from the kettle, then a good spray with starsan. When that's done I put the lid on and set it aside till I need it.

If you're planning on rehydrating dry yeast, now is also a good time to boil some water so that it has time to cool before using it.

About 10 mins before the end of the boil you can sanitise the wort chiller. To do this, set it on a chair beside the GF, connect the wort-in hose to the recirculation pipe and dangle the wort-out hose into the top of the GF. Don't worry about connecting the water in just yet.

8oV3k3J.jpg


Next, with the ball valve open, hit the pump button and the hot wort will begin to flow through the chiller, sanitising it. Stop the boil timer while this is happening, because the temperature will drop a few degrees. Circulate the wort through the chiller for about 5 mins or so.

When that's done, stop the pump and let the wort drain out of the chiller hose. When the temperature gets back up to boiling restart the boil timer. You can now connect the water-in hose (the blue one) to your water supply but don't turn it on yet. Position the water-out hose (the red one) so that it can drain safely. The wort chiller is now sanitised and ready to use.

Whenever your boil time is complete, switch off the heat then grab your paddle and give the wort a good stir for a couple of minutes to get a decent whirlpool going. Place the lid on the GF and let it settle for 5 mins. Doing this will help the wort flow a little easier without clogging the filter up during the next step.

While waiting, now is a good time to rehydrate your dry yeast if you're doing so.

At this point, I use another common little trick which is to remove the ball and spring from the check valve. The reason for this is that I've found the spring can get clogged up with hop material during the transfer, but for your first brew you may well want to skip this step because I know many people have no issue with this.

The check valve is the bit attached directly on top of the ball valve. Inside is a ball and spring which is a safety feature to prevent you from pumping hot wort all over your open-toed sandals, because the check valve will only open if the recirc arm or chiller is attached.

That means if you remove the ball and spring ensure that the ball valve is off and/or the recirc arm/chiller is attached before you switch on the pump!

So if you want to remove it, this is how. With the pump switched off (duh), grab the ball valve with one hand and with the other hand twist the check valve anticlockwise. It shouldn't be so tight that you can't loosen it by hand. Remove it carefully so that the spring doesn't fly away. Take out the ball and spring, put them somewhere safe, and replace the now empty check valve. Hand tight is good enough.

kVDTo7f.jpg


Now you're ready to begin chilling and transferring to the FV. Begin by turning on the water, and if you have a spare FV handy, you can collect the hot water coming out the other side for cleaning later. Then with the wort-out hose in the top of the FV switch on the pump. Grab your thermometer and check the temperature of the wort flowing out of the hose. Adjust the flow rate with the ball valve until it's as close as possible to your pitching temperature. I actually like to aim for a degree or 2 lower.

jFLiXWG.jpg


7soiyr2.jpg


During the transfer you may see the flow rate slow down as the filter gets caked with bits of hop. That's no big deal and you can adjust the ball valve to compensate. However if the flow gets very slow, even with the valve fully open, you can use your paddle to carefully scrape the filter. Be careful not to knock the filter off though. If this doesn't help, you might need to remove the ball and spring from the check valve as discussed above.

At the end of the transfer, I like to tip the GF towards the filter to get the last of the wort pumped out but be sure to switch off the pump before it runs dry, this isn't good for it.

Now the transfer is complete, check the temperature of the wort with a sanitised thermometer and if it's good, pitch your yeast, aerate and take an OG reading.

Now you can clean the GF. Start by tipping out the hop debris/trub into your bin/compost heap/prefered disposal method. Then pour a little warm water into the GF and use a sponge to clean off the worst of the residue. Tip out the water and repeat if necessary.

Then add 15L or so of water (the waste water from the chiller is ideal for this) to the GF, set the temperature to 60° and when it gets to temperature add 2 tablespoons of the GF cleaner. Attach the chiller and start the pump to recirculate the cleaner through it. There will probably be some wort in the chiller which will come out initially so dump this down the drain before putting the out tube into the GF.

W151nfa.jpg


Leave for 15 mins then swap the chiller for the recirc arm and leave for another 15 mins. Next you can discard the cleaning fluid by pumping or tipping it out. At this point I add some fresh water to rinse, again circulating through the chiller and the recirc arm for a couple of minutes. Again dump this water out, dry the inside with a clean cloth or tea towel, place all the various bits and pieces back inside and you're done!

Congratulations, you've just completed your first Grainfather brew, time to start preparing for the next one acheers.
Cheers Steve!
That was really a thorough description of a brew session using the GF! I would have avoid a lot of problems if I had read it before my initial brew sessions!
I liked very much the way you conducted the sparging. That is not the way I do but I'll surely try your method.
Which is the water:grist ratio you normally use for mashing? I've got the impression that the GF tends to have problems with the temperature control if will use thick mashes!
 
One tip I discovered during my last brewday was when transferring to the FV, pull the GF temerature probe out and stick it in the insulated pouch on the wall of the FV that the Inkbird probe sits in. (mine I made from a small piece of expanded polystyrene packaging and some gaffer tape) That way you can adjust the cooling water flowrate during transfer to hit your target pitch temp.

Which is the water:grist ratio you normally use for mashing? I've got the impression that the GF tends to have problems with the temperature control if will use thick mashes!

I always use the calculations done by the GF brewing software, from their website or app.
 
Hehehe spell checker! One question though... do you not vorlauf the wort through the grain bed to clarify it pre boil? The instructions say pour your sparge water over the filter but I wondered if you could also use the pump and continue to pass that over the grain bed as I do currently in my 3 vessel system.
 
Spell check gotcha, I'll let you off.
I use a robobrew and guten so the same really.
I run the pump all the time during the mash, so the wort is clear long before the end of the mash.
Then at end of mash / mash out really stop the pump raise the malt pipe and then sparge with it set to boil. Remove malt pipe and sit it in bucket, give it a good squeeze add in that liquid if gravity high and i need the numbers.
Does that make sense?
 
Leave the basket sitting in place to drain until the wort gets up near boiling point, but be sure to remove it before it actually starts boiling. This is a surefire way of having a boil over. By the time the wort gets to mid 90s the basket should be well drained, so set it aside for now and turn your attention back to the GF.

Be sure to keep the lid off from now until the end of the boil. As the wort comes to the boil it'll begin to foam up. Stir this back in to prevent boil overs, it'll settle down after a few minutes.

GnnHMap.jpg


As soon as you have a nice rolling boil, start a timer with your boil time and add the hops as per your recipe.

Every 15 mins or so during the boil, take your paddle and gently scrape the bottom of the boiler to prevent proteins scorching on the bottom.

Now is a good time to dispose of the used grain and clean the grain basket, plates, pipe work and overflow inlet. I do this outside because it can be a bit messy. Dismantle all the various parts and rinse under a tap. Use a non-scratch scouring sponge to remove any stubborn residue.

Once these bits are clean and dry, they can be put aside for storage, you're done with them for today.

Towards the end of the boil you want to start thinking about sanitising the FV. I do this by giving it a rinse out with boiling water from the kettle, then a good spray with starsan. When that's done I put the lid on and set it aside till I need it.

If you're planning on rehydrating dry yeast, now is also a good time to boil some water so that it has time to cool before using it.

About 10 mins before the end of the boil you can sanitise the wort chiller. To do this, set it on a chair beside the GF, connect the wort-in hose to the recirculation pipe and dangle the wort-out hose into the top of the GF. Don't worry about connecting the water in just yet.

8oV3k3J.jpg


Next, with the ball valve open, hit the pump button and the hot wort will begin to flow through the chiller, sanitising it. Stop the boil timer while this is happening, because the temperature will drop a few degrees. Circulate the wort through the chiller for about 5 mins or so.

When that's done, stop the pump and let the wort drain out of the chiller hose. When the temperature gets back up to boiling restart the boil timer. You can now connect the water-in hose (the blue one) to your water supply but don't turn it on yet. Position the water-out hose (the red one) so that it can drain safely. The wort chiller is now sanitised and ready to use.

Whenever your boil time is complete, switch off the heat then grab your paddle and give the wort a good stir for a couple of minutes to get a decent whirlpool going. Place the lid on the GF and let it settle for 5 mins. Doing this will help the wort flow a little easier without clogging the filter up during the next step.

While waiting, now is a good time to rehydrate your dry yeast if you're doing so.

At this point, I use another common little trick which is to remove the ball and spring from the check valve. The reason for this is that I've found the spring can get clogged up with hop material during the transfer, but for your first brew you may well want to skip this step because I know many people have no issue with this.

The check valve is the bit attached directly on top of the ball valve. Inside is a ball and spring which is a safety feature to prevent you from pumping hot wort all over your open-toed sandals, because the check valve will only open if the recirc arm or chiller is attached.

That means if you remove the ball and spring ensure that the ball valve is off and/or the recirc arm/chiller is attached before you switch on the pump!

So if you want to remove it, this is how. With the pump switched off (duh), grab the ball valve with one hand and with the other hand twist the check valve anticlockwise. It shouldn't be so tight that you can't loosen it by hand. Remove it carefully so that the spring doesn't fly away. Take out the ball and spring, put them somewhere safe, and replace the now empty check valve. Hand tight is good enough.

kVDTo7f.jpg


Now you're ready to begin chilling and transferring to the FV. Begin by turning on the water, and if you have a spare FV handy, you can collect the hot water coming out the other side for cleaning later. Then with the wort-out hose in the top of the FV switch on the pump. Grab your thermometer and check the temperature of the wort flowing out of the hose. Adjust the flow rate with the ball valve until it's as close as possible to your pitching temperature. I actually like to aim for a degree or 2 lower.

jFLiXWG.jpg


7soiyr2.jpg


During the transfer you may see the flow rate slow down as the filter gets caked with bits of hop. That's no big deal and you can adjust the ball valve to compensate. However if the flow gets very slow, even with the valve fully open, you can use your paddle to carefully scrape the filter. Be careful not to knock the filter off though. If this doesn't help, you might need to remove the ball and spring from the check valve as discussed above.

At the end of the transfer, I like to tip the GF towards the filter to get the last of the wort pumped out but be sure to switch off the pump before it runs dry, this isn't good for it.

Now the transfer is complete, check the temperature of the wort with a sanitised thermometer and if it's good, pitch your yeast, aerate and take an OG reading.

Now you can clean the GF. Start by tipping out the hop debris/trub into your bin/compost heap/prefered disposal method. Then pour a little warm water into the GF and use a sponge to clean off the worst of the residue. Tip out the water and repeat if necessary.

Then add 15L or so of water (the waste water from the chiller is ideal for this) to the GF, set the temperature to 60° and when it gets to temperature add 2 tablespoons of the GF cleaner. Attach the chiller and start the pump to recirculate the cleaner through it. There will probably be some wort in the chiller which will come out initially so dump this down the drain before putting the out tube into the GF.

W151nfa.jpg


Leave for 15 mins then swap the chiller for the recirc arm and leave for another 15 mins. Next you can discard the cleaning fluid by pumping or tipping it out. At this point I add some fresh water to rinse, again circulating through the chiller and the recirc arm for a couple of minutes. Again dump this water out, dry the inside with a clean cloth or tea towel, place all the various bits and pieces back inside and you're done!

Congratulations, you've just completed your first Grainfather brew, time to start preparing for the next one acheers.
Hi all, did my first ever AG brew yesterday using a G30 and this excellent post as a reference along with advice hints and tips from another member on here, ecirpian. Whilst it mostly went very well, the false bottom I purchased tilted and I ended up with the filter being knocked off (SS jubilee clip inbound) I have read this is a common problem but haven’t found a solution, has anyone come up with a solution to keep the FB in place?
TIA.
 
I recently got a false bottom. I can't imagine how it would tilt, the supplied screw in legs seemed to make a very stable platform. But I have only used it once. One additional point, I did find that (paradoxically) it allowed more fine debris to pass through the filter, presumably because the coarse material that usually strains it out was held back by the FB and for the first time I got clogging in the check valve. Next time I will probably remove this as per another tip in this thread.
 
I think the FB most likely lifted due to the boil, then started to move about, I noticed it when I put the paddle in for a stir. It pushed back down easy enough but every time I put the paddle in it was back up again. I did the cam lock conversion so had no trouble with a blockage at the valve.
 

Latest posts

Back
Top