My cheap, simple AG setup

The Homebrew Forum

Help Support The Homebrew Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

karloz

Member
Joined
Jun 22, 2013
Messages
52
Reaction score
11
Location
Grimsby, UK
So after using kits for a while, I decided to attempt AG. Not wanting to spend a fortune, I thought I would build my own equipment and upgrade as I go.

I am a total beginner at this so I watched a lot of videos and set at it. Yesterday I completed my first AG and it seemed to go ok (apart from the few lessons learnt found here http://www.thehomebrewforum.co.uk/showthread.php?t=71663)

Boil kettle:

Equipment used:
30l FV
2x Tesco value kettles (£6 each)
15mm Compession tank connector (£2.32 toolstation)
Copper pipe (B&Q £6.24 3m x 15mm - This is enough for the mash tun too)
Ball valve to fit 15mm copper pipe (I liberated mine from work)
40mm & 20mm Hole saw (these were my measurements)
Sandpaper
PTFE tape (use it on every thread throughout)

First I took the kettles to pieces and removed the elements to fit. I measured the elements and found I needed a 40mm hole saw. There is a small metal disc inside that has to be removed, otherwise when it hits boiling it will cut off.
I then drilled, sanded and fitted them:

EDIT: I had a few problems with leaks from the kettle elements when in place. The wall of the kettle was slightly thicker than the FV. I ended up doubling the seals with some spare bits I had kicking about.

IMG_0870.jpg

IMG_0869.jpg


I then drilled a 20mm hole, sanded and fitted the tank connector, small length of copper pipe to a valve and another piece of copper pipe (followed by jubilee clipped hose)

IMG_0867.jpg


I took a small length of copper pipe for a 'false bottom', however this proved a problem so I am going to change this to a 'flexible tap connector' with the rubber hose taken out of the middle (just leaving the mesh)

IMG_0868.jpg



Mash Tun

Equipment used
12l Cool box (£9 poundstretcher) I may get a bigger size though
15mm Compession tank connector (£2.32 toolstation)
Ball valve to fit 15mm copper pipe
15mm Copper pipe 't' pieces and elbows
Copper pipe from above
16mm & 20mm drill bits/hole saws
1mm drill bit or similar

Firstly, I drilled through the bottom corner and fitted the tank connector, connected to ball valve (same as for boil kettle). I did have to make a bigger hole on the outside to fit a spanner in.

IMG_0871.jpg

IMG_0874.jpg


I then created my inner piping for the grain bed and drilled lots of small holes in it. This just slots into the tank connector. I didn't weld it together for easy cleaning:

IMG_0875.jpg

IMG_0876.jpg


Next, Sparge arm. I drilled a 16mm hole in the top of my cool box and poked a small length of copper pipe through.

IMG_0872.jpg


Inside, push fitted together i created the sparge arm by drilling 1mm holes.

IMG_0873.jpg



Wort chiller

Equipment used:
Wednesbury copper compression tube 8mm x 10m (£14.78 B&Q)
Hose pipe
Jubilee clips

Easy one. Just wrapped the copper pipe around a paint tin and connected the hose pipe to each end.

IMG_0878.jpg

IMG_0879.jpg


Final set up...

IMG_0865.jpg


I hope this is of some use to someone...
 
What size hose are people using to connect onto 15mm copper pipe?

Something about 15mm inside diameter, heat it up with hot water if its on the tight side to expand the hose. If you need to connect onto 10mm copper with a garden hose you can solder on a 10mm x 15mm reducer onto the 10mm end, that will give you a clean 15mm copper pipe end to attach the hose to.
 
Awesome. Great pics and write up.
Wanted to respond so can easily find this in the future when the inevitable happens and I move on a level.
Dave
 
I did something similar with mine, I both mash and boil in the same fv. No need for mashtun, I only loose about 0.5 celsius in 60 min. I made a element protector out of some aluminium I had around. I also made a place to put the mashbag when draining and I cut out the bottom of a second fv to avo7d spilling. It works great! 68%-73% efficiency on 3 brews so far. I sparge with about 10 liters.

Kettle elements are from eBay for about 5pounds each and came with rubber fittings. No leaks so far! I get a really good boil, so good that I have to disconnect one of the elements after start of boil
IMG-20180821-WA0007.jpg
IMG-20181109-WA0023.jpeg


Mashing!
IMAG2611.jpg
IMG-20180820-WA0009.jpg
IMG-20180822-WA0004.jpg
 
I gotta lotta respects for guys who make up their own brewing kits, it's all part of brewing a great beer! To say that you made all the kit and completely brewed from scratch is admirable. You can really sit back and enjoy a home brew and say "I did all that". There are even guys on this forum who cultivate their own yeasts, grow their own hops, condition their own water, I'm now waiting for someone to actually grow their own barley and process it, bet It wont be long before someone chimes in and says they've done just that.
 
I gotta lotta respects for guys who make up their own brewing kits, it's all part of brewing a great beer! To say that you made all the kit and completely brewed from scratch is admirable. You can really sit back and enjoy a home brew and say "I did all that". There are even guys on this forum who cultivate their own yeasts, grow their own hops, condition their own water, I'm now waiting for someone to actually grow their own barley and process it, bet It wont be long before someone chimes in and says they've done just that.
Ive seen some post here in Norway about people doing exactly that.
It's fun to make your own stuff! Fun and a lot cheaper. Cultivating yeast is not hard, making a magnetic stirrer for the yeast is not hard, top and bottom cropping yeast is not hard. Just try it. You'll save money and in the end you'll have a &#%@load of different yeast to choose from.

Here is easy version magnetic stirrer
IMG-20180925-WA0005.jpeg

Here is my newest one, a little more but still easy. It was made from 2 wooden napkinholders and some cheap China parts. Total cost about 15 pounds
IMAG2967.jpg

IMAG2971.jpg

IMAG2958.jpg

IMAG2973.jpg


Here is a pic of some kveik yeast that I cultivated.
IMAG2745.jpg


Beer is awesome. Making it your own is even better! acheers.
 
Last edited:
Really fascinating and inspiring posts! I am so looking forward to having the space & time to move on to AG, and although shiny
Grainfathers etc look gorgeous, the home brewed hardware has a charm all of its own - and saves hundreds of ££!

btw @Soyyojuli - what method do you follow to make the yeast stirrer? Looks sweet :-)
 
My setup is very similar to the OP's but a bit simpler, I used a bazooka filter both as the hop filter and in the mash tun, I didn't bother with a sparge arm and just batch sparge and used plastic taps. I think I used exactly the same cool box but used the thicker PP 33l bucket which is thicker, batch sparging I don't need any hose which I prefer. Your setup looks better than mine but I am worried you may have some brass fittings on the tank connector which could leach stuff into the beer.
 
Really fascinating and inspiring posts! I am so looking forward to having the space & time to move on to AG, and although shiny
Grainfathers etc look gorgeous, the home brewed hardware has a charm all of its own - and saves hundreds of ££!

btw @Soyyojuli - what method do you follow to make the yeast stirrer? Looks sweet :-)

Glad you like it :laugh8: I've been told its a bit flashy haha.

It basically a pc fan hooked up to a potensiometer and a switch from there. It's all hooked up to a 12v phone charger I had laying around.
The box is just two wooden napkinholders that I put together with some screws. I burned in the drawing with a small welder. Used some left over cables I had from other pc parts.

The China parts are from Jolly. Really cheap and free shipping. (if you can wait a month)

If you want a part list I'll gladly post it.
 
Do either of you guys use any sort of temperature controller?

I have an old fermentation bucket that I was thinking about using to make a ebiab setup, but it would be handy if I could hold a mash temperature.
 
Do either of you guys use any sort of temperature controller?

I have an old fermentation bucket that I was thinking about using to make a ebiab setup, but it would be handy if I could hold a mash temperature.

I use a digital thermometer. I put it in the hole on the lid of the bucket. I've thought about installing a thermowell but haven't really gotten to it. I just stick the thermo in and let it sit there during the wholeash
Never had more than 1 Celsius drop
 
Really fascinating and inspiring posts! I am so looking forward to having the space & time to move on to AG, and although shiny
Grainfathers etc look gorgeous, the home brewed hardware has a charm all of its own - and saves hundreds of ££!

btw @Soyyojuli - what method do you follow to make the yeast stirrer? Looks sweet :-)

here's steve's guide to making a magnetic stirrerhttps://www.thehomebrewforum.co.uk/threads/how-to-build-a-stir-plate-for-less-than-ten-quid.65471/
 
Back
Top