Ghillie's Keezer Build Thread

The Homebrew Forum

Help Support The Homebrew Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Arrived home yesterday afternoon and collected the freezer last night.

5 kegs will fit with ease, although I think I'd be unable to remove the front ones as the tap shanks will be in the way.

Any thoughts guys? It's looking like a 4 keg keezer.

View attachment 17825 View attachment 17826
Ghillie, looking at the way your kegs are higher than the lip of the keezer, and the thickness of the lid protrusion I'm wondering what size timber your going for. I used 4 x 2 but my kegs sit lower than yours and the lid doesn't protrude as much.
 
Ghillie, looking at the way your kegs are higher than the lip of the keezer, and the thickness of the lid protrusion I'm wondering what size timber your going for. I used 4 x 2 but my kegs sit lower than yours and the lid doesn't protrude as much.
The external lip is 1", so if my joiner pal can source some of that then perfect. That gives me a total of 2" between the exterior and interior. So 5 kegs with 2" shanks may well work.
 
Hi @Ghillie
Five kegs will be a tight fit, but they will fit!
Any problems removing the front kegs could be resolved by removing one of the rear kegs, "shuffling" the others around so that the front kegs move to the rear. A faff, I know, but do-able.
A less pallatable solution would be to space the taps out around three sides of the keezer so that they do no rextrict access. This will spoil the aesthetics but it would be a possible solution.
With 5 kegs, there is bound to be a couple of beers that are less popular than the others - put them to the front.
Next idea - direct from Heath Robinson! Split the front part of the collar, hinge the top half and mount your taps on that part. When a keg needs to come out, swing the tap section forward, thus getting them out of the way.
I'm ready for my medicine, nurse!
 
Hi @Ghillie
Five kegs will be a tight fit, but they will fit!
Any problems removing the front kegs could be resolved by removing one of the rear kegs, "shuffling" the others around so that the front kegs move to the rear. A faff, I know, but do-able.
A less pallatable solution would be to space the taps out around three sides of the keezer so that they do no rextrict access. This will spoil the aesthetics but it would be a possible solution.
With 5 kegs, there is bound to be a couple of beers that are less popular than the others - put them to the front.
Next idea - direct from Heath Robinson! Split the front part of the collar, hinge the top half and mount your taps on that part. When a keg needs to come out, swing the tap section forward, thus getting them out of the way.
I'm ready for my medicine, nurse!
Not such a bad idea although I'd just go for a piano hinge along the bottom of the whole front section.
 
Not such a bad idea although I'd just go for a piano hinge along the bottom of the whole front section.

Or just hinge the entire length at one end, like a hypercar door. :?::thumba:

Edit: Actually, just use a couple of strong magnets and the whole front could come off.
 
Not such a bad idea although I'd just go for a piano hinge along the bottom of the whole front section.
Hi!
I was concerned about a good seal and firm adhesion. I would also worry about fixing the hinge to the freezer body, but hey! I'm a worrier!
I thought that perhaps a couple of fastenings could be fixed on the inside of the collar to hold the folding section tight when not folded.
 
Keezer lid removed and masked with tape ahead of painting...

1549648623770811.jpg


Sketched around the controller and drilled a really ugly 22mm hole to cut and file around.

1549648624129438.jpg


Still ugly after filing...

1549648624447216.jpg


First coat of satin black, couldn't find matt in B&Q so that will have to do. Not bad so far, the second and final coat later tonight.

1549648623186817.jpeg


So regarding the collar, a hinge option would be pretty cool and handy. Will have to think about the easiest way of making it functional as well as airtight...
 
Thanks @Bigcol49, I did see a lot of Yanks doing that. Makes sense. Weather strip (or something like that I think it's called, for windows and doors) glued to the underside of the collar to seal against the top of the freezer.

The only issue with that really is how far away from the wall it will need to sit in order to open the lid. No massive drama tbh, but makes the small garage even smaller...
 
The only issue with that really is how far away from the wall it will need to sit in order to open the lid.
You would need to open the full lid only rarely. You can get "castors" for heavy white goods to sit on to make it easy to move them, but that's more expense. Two steps forward, one step back!
 
The external lip is 1", so if my joiner pal can source some of that then perfect. That gives me a total of 2" between the exterior and interior. So 5 kegs with 2" shanks may well work.
24mm ply is what I used on mine for the collar. Less chance of warping than ‘real’ wood.
 
Cheers guys!

Was thinking the casters route initially Colin but then thought "I've nowhere to wheel it to..."

Wheeling it out from the wall when I need to change kegs would be a game changer!
 
Have you thought about how you're going to lift full kegs into the freezer? I think I'll be able to fill mine in-place but will have to do some height measuring to be certain.

I want to avoid having to lift and lower them when full because one day I can see that going badly wrong.
 

Latest posts

Back
Top