Flexible gas line.

The Homebrew Forum

Help Support The Homebrew Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Snoop

Active Member
Joined
Jun 16, 2014
Messages
70
Reaction score
28
What do I need to buy to move from the usual 3/8 rigid gas line to the flexible tubing I always see the yanks using? The rigid stuff is just a massive pain in my fridge.

It's all 3/8s to JG pushfit. Mostly cornies but a few Sankeys too. I gather I would need to replace the JG push pit with hose barbs for the flexible line? The regulator ends of the lines are all JG too, standard thread size for the regulators I think. Not sure what exact size but I have 3 regulators and all the JG fittings fit so guess it's fairly standard.

Not entirely sure where to start. I see the stuff does exist but not sure what to buy and with what fittings :)

Ta
Si
 
I'm moving to 3/16 for the short gas lines in my keezer build because of the flexibility issue. 3/16 JG connectors are only available as reducers from 3/8 so you do still need 3/8 fittings for the final endpoints with a small run of 3/8 to the reducer:

Gas -> 3/8 -> 3/16 -> 3/8 -> keg
 
I use these for the beer lines and they work well. A bit slow but I can wait. wasn't sure if they were suitable for gas tho.
 
Goin to 3/16 would work well. Can it hold reasonably high pressures? Sometimes I carb in bursts at 40psi. I never considered using the same setup as my beer lines for the gas.
 
I agree, it's a bit too rigid.
@LeeH what size of that coiled stuff is required? And are any extra fittings required to use that stuff?
 
Goin to 3/16 would work well. Can it hold reasonably high pressures? Sometimes I carb in bursts at 40psi. I never considered using the same setup as my beer lines for the gas.
Yeah it's fine. It'll be good for the same pressures that 3/8" can take.
 
Goin to 3/16 would work well. Can it hold reasonably high pressures? Sometimes I carb in bursts at 40psi. I never considered using the same setup as my beer lines for the gas.
Since the beer out will be at the same pressure as the gas in I would assume it can take a similar pressure, many pubs serve everything at 35 psi as standard so an extra 5 would not be an issue.
 
All my gas line is polyurethane. The aquarium bunch use it because it is good with CO2 (don't use silicone - leaks like a sieve). Those curly "pig tail" lengths look pretty good.

I get all mine from Context Pneumatics along with the "KELM" fittings (which are a hell of a lot cheaper then JG, and made of metal too).

I still use the rigid MDPE (polythene) stuff for beer-line.
 
I agree, it's a bit too rigid.
@LeeH what size of that coiled stuff is required? And are any extra fittings required to use that stuff?

I use 8mm as they were free to me but any smaller side is fine. You don’t need wide bore gas lines.

Fittings are just normal push fits.
 
@LeeH So if I ordered the 8mm x 5mm that would suit my current set-up (refurb corny set-up from Malt Miller) and that would be it? Nothing extra? Because that would be class.
 
Good info here. On that curly pipe from eBay are you saying that works with JG 3/8 push fit connectors? As I already have lots of those attached to my disconnects. So sounds like a plan if that works
 
All my gas line is polyurethane. The aquarium bunch use it because it is good with CO2 (don't use silicone - leaks like a sieve). Those curly "pig tail" lengths look pretty good.

I get all mine from Context Pneumatics along with the "KELM" fittings (which are a hell of a lot cheaper then JG, and made of metal too).

I still use the rigid MDPE (polythene) stuff for beer-line.

Those push fit connectors do look alot cheaper than JG ones. Which size do you use? The amount of them is a bit overwhelming and I'll probably order the wrong ones. Any idea which ones screw onto a corny disconnect and also into a regulator?
 
Those push fit connectors do look alot cheaper than JG ones. Which size do you use? The amount of them is a bit overwhelming and I'll probably order the wrong ones. Any idea which ones screw onto a corny disconnect and also into a regulator?
Ah. Yes the choice is a bit over-whelming. But sizes are down to whatever you chose to connect: For hose I use 4mm ID (PU06/040B) for my feed lines (0-20psi) and 6mm ID for bus lines (3-5bar - the lines connecting primary to secondary regulators), simply so I don't mix them up (I don't fancy beer served at 5bar - 75psi). Threaded connectors always seem to be BSP from Kelm - I will normally chose 1/4" BSPP (parallel, there will also be BSPT, tapered, fittings). Very occasionally I use 1/8" BSPP. Fittings for Corny disconnects aren't by Kelm but Context Pneumatics sell them. The threaded disconnects are 1/4" MFL, or "flare". You don't look for these but for 7/16" JIC (confusing, but they are all US UNF threads at heart). I'm not sure if the mating "cone" on JIC and "flare" are the same (38 or 45 angle) but disconnects have plastic "cones" and the few brass "cones" I have seal faultlessly so doesn't really matter. You want part "2BJ0407" (for 1/4" BSPP) which you find here: https://www.contextpneumatics-catal...17167&level2=16869&level1=1&stockistown=False. Note the BSPP threads on these have no seal, you'll need a few wraps (7 is "standard") of PTFE tape on them.

Hose is here: https://www.contextpneumatics-catal...3&level2=35072&level1=30062&stockistown=False. So 25m will last you sometime! But it's filthy cheap.

I use the "finger-tight" fittings. They don't leak (pushfits do!). PDF attached.

Here's some in action ("spunding" valves):
20190115_200855_WEB.jpg
 

Attachments

  • KELM Quickfit Fittings.pdf
    1.3 MB · Views: 180
Thanks very much for this! I use the same secondary regulators and I like the way you have it right at the disconnect. That's a good idea.
 
Thanks very much for this! I use the same secondary regulators and I like the way you have it right at the disconnect. That's a good idea.
Don't be fooled by the piccie. I really do use the regulator (Shako NR200) as a spunding valve! There is 20L of fermenting beer in that keg (old piccie so that beer is being drunk now - still in the same keg - and another fermenting beer has taken its place).
 

Latest posts

Back
Top