Quantcast

Search results

Help Support The HomeBrew Forum:

  1. emerson909

    Issue with Inkbird ITC308S - anyone else had this?

    Ey up Bezza, I’ve spent over £100 on these things and each one has failed in exactly the same way. Inkbird claim it is a probe failure yet I have replaced the probe on one unit at their suggestion and it had no effect. They seem to suggest I am using the probe in some manner that is causing it...
  2. emerson909

    Issue with Inkbird ITC308S - anyone else had this?

    Inkbird have kindly agreed to send me a replacement unit, out of the warranty period. The reason they give for the fault is a broken probe. Will report back when the replacement fails
  3. emerson909

    Issue with Inkbird ITC308S - anyone else had this?

    Happy to apologise when they literally sort it out
  4. emerson909

    Hand Pull Beer Engine

    not to start an argument but I’ve picked up two second hand beer engines and they are superb. Both needed a bit of tlc but they are so simple and parts are readily available if needed. I have set up per @peebee excellent advice and the beer runs out way before any loss in quality. Both are...
  5. emerson909

    Issue with Inkbird ITC308S - anyone else had this?

    It’s complete bollocks, they work fine for a few months then suddenly the reading starts going haywire despite the probe being in exactly the same position. If @Inkbird where actually interested in trying to solve the problem they might have asked for some of us to send the faulty units in to...
  6. emerson909

    Ubidots variable resolution

    Yeah that has sorted it, what a strange place for the setting, I wouldn't have found that in a million years! Thanks athumb..
  7. emerson909

    Ubidots variable resolution

    Anybody else noticed a change in their ubidots plots? I have SG as a calculated variable but it has recently started to only plot to 2 decimal places, it used to show a smooth curve but now just shows step changes as below. Can't work out why it is doing it, any ideas?
  8. emerson909

    Beer Engine Cleaning

    It’s all about balance, you only need 1/2 tsp VWP at flameout 😂
  9. emerson909

    Beer Engine Cleaning

    The seals on my cylinder were pretty funky so I replaced those, these guys should be able to sort you out Home page - Hand Pumps, Beer Pumps, Fonts, Gas Regulators, Cask Craft Ale, Beer Engines, Spares, Aspirator Breather
  10. emerson909

    Beer Engine Cleaning

    I have just refurbished a hand pull from eBay, I used sodium percarbonate to clean everything and it came up pretty good. I use this now after a keg to clean which seems to work pretty well We Can Source It Ltd - Pipeline... https://www.amazon.co.uk/dp/B07RLHRS5K?ref=ppx_pop_mob_ap_share Not...
  11. emerson909

    Beer Engine Cleaning

    Vwp is worth a try
  12. emerson909

    Beer line full of bubbles!

    If the lines are in the fridge then the temp must be constant so it must be pressure drop causing the co2 to come out of solution. If it happens when the beer is flowing then it must be caused by a restriction in the line somewhere so yeah if it’s a specific keg the dip tube might be a good...
  13. emerson909

    Beer line full of bubbles!

    Those gas lines to the keg look pretty small, you might not have enough gas flow when serving, that would drop pressure causing co2 to come out of solution
  14. emerson909

    Beer line full of bubbles!

    What pressure is your reg set to and what temp is the kegerator?
  15. emerson909

    Water for a Munich Helles

    Your water looks pretty good for helles, I would just add acid to get to 5.3 pH, see what that batch tastes like and adjust from there
  16. emerson909

    Sparging - BIAB

    The only thing I have to watch for on my system is the recirculation rate, too low and I don’t get a good temperature control, too fast and I don’t get enough flow through the bag. Currently looking at solutions to this, think I’m going to split the recirc flow between the lid and the whirlpool...
  17. emerson909

    Sparging - BIAB

    Yes it works perfectly. I don’t sparge and mash with full volume. I recirc during the mash and do a mash out for 20 mins with a good stir before removing the grains. I consistently get 70% mash efficiency, bit lower for higher gravity brews. Personally I don’t see the point in adding extra steps...
  18. emerson909

    foxbat's brewdays

    @The-Engineer-That-Brews https://www.themaltmiller.co.uk/product/large-hydrometer-1000-1060/ I’ve got this one, it’s really easy to read
  19. emerson909

    Fermzilla 30L All rounder ?

    I’m very happy with mine
  20. emerson909

    Issue with Inkbird ITC308S - anyone else had this?

    No not PID controllers, just discrete on/off. There’s definitely no integral time to adjust anyway. I have a video where the PV goes from 21, to 20 and kicks heating on then back to 21.5 within a second, there’s just no way the actual temp can change that fast so must be electrical fault.
Top