• If you have bought, sold or gained information from our Classifieds, please donate to The Homebrew Forum and give back.

    You can become a Supporting Member or just click here to donate.

Complete 100L 3V HERMS Brewery for Sale

The Homebrew Forum

Help Support The Homebrew Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Status
Not open for further replies.

hambrook

Active Member
Joined
Dec 19, 2014
Messages
66
Reaction score
2
Location
Emsworth, Hampshire
Complete 100 Litre HERMS Brewery For Sale
3 Vessel Stainless Steel Set up 100L SS Fermenter


This ‘Turnkey’ 100L HERMS brewery setup is based on plans from the Electric Brewery.com and built by the respected Powell Brewing. It contains everything you need to start and run a small micro-brewery, just add the silicon tubing! It's all working and running a small commercial brewery that brews once a week until my new equipment arrives from Italy. This 3V All Grain HERMS set up has made some award winning beers and is only being sold due to expansion.

It has the ability to brew 2x 9gal casks (80L) per batch with a very high brewhouse efficiency (around 90%) due to the ability to do step mashes and re-circulating through the HERMS coil. The whole thing is powered with one 32A supply to the control box, from there the power is distributed to each element.

You can mash in at around 70c and then just set the desired mash temp on the controller and leave it. The temp will stabilise and maintain itself so you always get the mash spot on. It really is a dream to use compared to other systems I’ve used.

The 2x 3kW elements in the boil kettle mean you can get a very vigorous rolling boil in about 30mins, then switch one element off to maintain a steady rolling boil. It can handle both whole leaf or pellet hops due to the whirlpool port and side filter in the Boil Kettle, so you can make some really flavourful beers.

The fermenter is completely temperature controlled so you can create any style of beer no matter what the outside temps are. It will cool down to 2c for crash cooling at the end of fermentation so you will get a very clear final product without the use of finings.

I have an operating manual and step by step brew day instructions.

The whole thing is freestanding on a custom made Stainless steel table, which can be included in the sale. Total cost spent was about ��£3k (and a lot of time!) on all the listed parts separately and I'm looking for ��£1900 for the complete setup including the custom made brew stand.

Images & Full Advert here: https://goo.gl/v8Pm7L

Boil Kettle
• 100L Stainless Steel Pot
• 2 x Stainless Steel Ball Valve ½” taps
• 2 x Stainless Steel Cam & Groove Male ½” connectors
• 2 x SS 90 degree Elbow connectors (one for filter outlet, one for whirlpool inlet)
• 2 x 3kW Elements
• Stainless Steel ‘Bazooka’ Type Hop Filter
• 1 x NTC temp probe
• 1 x Analog 0-120c temp dial
• Sight glass 5L graduations

Mash Tun
• 100L Stainless Steel Pot
• 2 x Stainless Steel Ball Valve ½” taps
• 2 x Stainless Steel Cam & Groove Male ½” connectors
• Stainless Steel False Bottom Grain Filter
• 1 x Analog 0-120c temp dial
• 1 x NTC temp probe (in MT outlet) for connection to the STC Controller
• Sight glass 5L graduations

Hot Liquor Tank
• 100L Stainless Steel Pot
• 4 x Stainless Steel Ball Valve ½” taps
• 4 x Stainless Steel Cam & Groove Male ½” connectors
• Copper HERMS Coil
• 1 x 3kW Element
• 1 x 1kW Element (linked to STC temperature controller to regulate mash temp)
• Sight glass 5L graduations
• 1 x Analog 0-120c temp dial
• 2 x NTC temp probes (one in pot, one in HERMS Coil outlet)

Fermenting Vessel
• 100L Stainless Steel Pot
• 2 x Stainless Steel Ball Valve ½” taps
• 2 x Stainless Steel Cam & Groove Male ½” connectors
• Deck drain fitting for total contents drain
• 1 x Stainless Steel 90 degree elbow fitting
• 1x NTC temp probe
• 2 x 25w Heat pads
• Double wall Insulation sides & Base
• 10m x 3/8’’ SS cooling coil
• Stand
 
Control Box
• 32a MK commando Socket (main power supply)
• 3 x STC-1000 Controllers
• 6 x 20amp switches (4 for elements, 2 for pumps)
• Timer
• 4 x 20amp Neutrik sockets
• 4 x 20amp Neutrik plugs (one for each element)
• 2 x IEC sockets for pumps
• 2 x IEC plugs for pumps
• 3 x temp probe sockets
• 3 x temp probe plugs

Pumps and Chiller
• 2 x Flojet pumps
• 6 x Stainless Steel Cam & Groove Male ½” connectors
• 2 x Stainless Steel Ball Valve ½” taps
• 1 x 30 Plate Wiltec 125kw Stainless Steel Counterflow Plate Chiller

��£1,900
Collection from Emsworth, Hampshire. PO10


IMG_9842 (1).jpg
 
Status
Not open for further replies.
Back
Top