Low alcohol cerveza kit?

The Homebrew Forum

Help Support The Homebrew Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

Shirley Bassett

Regular.
Joined
Aug 15, 2018
Messages
443
Reaction score
486
SWMBO likes low or zero alcohol lager type beer, such Budweiser Prohibition or Becks blue etc.

She‘s asked is it possible to ferment a Wilco Cerveza kit without adding the recommended 1kg of sugar, and if so what alcohol % would the kit produce.

She isn’t adverse to consuming alcohol, in fact she drinks Malbec and the like at 14%.
 
Around 2% or so. If that's the plan, then extra precautions with sanitation, as 2% ABV is not as effective an anti-bacterial as 4%?

Nothing wrong with low alcohol drinks, of course, and this sort of approach might be fine.
 
Slid,

Thanks for the response.

I wasn’t sure the kit would ferment.

I usually batch prime “full strength” kit at 8g / litre.

I was always led to believe that 20g of sugar in 1 litre of water / beer would produce around 1% alcohol.

I therefore assume the end product would be under 2.5% alcohol when primed, or have you accounted for carbonation in the 2% answer?

I usually wash buckets and utensils in 60C soapy water, and then rinse in cold, and Starsan everything, either a good glug in the bucket and mist everything else. Is this sufficient sanitisation.
 
Yeah
Slid,

Thanks for the response.

I wasn’t sure the kit would ferment.

I usually batch prime “full strength” kit at 8g / litre.

I was always led to believe that 20g of sugar in 1 litre of water / beer would produce around 1% alcohol.

I therefore assume the end product would be under 2.5% alcohol when primed, or have you accounted for carbonation in the 2% answer?

I usually wash buckets and utensils in 60C soapy water, and then rinse in cold, and Starsan everything, either a good glug in the bucket and mist everything else. Is this sufficient sanitisation.

I would say the sanitation is fine. If you get good results at 8g per litre priming, that is OK with me, but it seems like a lot.

Your 20g sugar in 1litre water approximating to 1% alcohol sounds good to me. So in a 23L batch you add 184g of priming sugar - that would make for 2.4% or so, right enough. In my early kit brewing days, and most of us here did them, I would go 200g in 25L and am still here.
 
Yeah


I would say the sanitation is fine. If you get good results at 8g per litre priming, that is OK with me, but it seems like a lot.

Your 20g sugar in 1litre water approximating to 1% alcohol sounds good to me. So in a 23L batch you add 184g of priming sugar - that would make for 2.4% or so, right enough. In my early kit brewing days, and most of us here did them, I would go 200g in 25L and am still here.
I'm 99% certain that 8g of dextrose per litre, is the same as using two Coopers carbonation drops in a 740ml pet bottle, which they recommend.
So there would be quite a lot of people priming at that rate.
I don't mind it for Lagers. Maybe a tad too much for Ales.
 
I usually prime pressed cider at 10g / litre,
Cerveza at 8g and stout at 6g.

I learnt quite quickly that 10g was too much for beer.
 
Think I would make it to at least 4% abv then dilute it with boiled water at bottling. Add your priming sugar to this water.

Less than 4% abv is just too much risk of infection.
 
I like the idea of brewing it at 4% and then diluting it down at the end stage with boiled water. Therefore I’ve added 1kg of dissolved sugar to this batch and will have to fall on my sword and drink it when it’s ready.

The next one I’ll brew at 10litres and dilute it down when I batch prime and bottle.
 

Latest posts

Back
Top